![]() We are aware that this is not a good user experience and hope to improve this in a future release.1.189 FAQ-889 How to add asymmetric error bars for your 2D or 3D plot? If you don't want the top-most layer to appear in the legend you can toggle its visibility in the Contents pane. If the top-most sub-layer is not the top-most legend item toggling the visibility does not work. In order to successfully toggle the visibility of the the Group layer name the top-most member layer of the group needs to be in the legend and this item needs to be listed above all the other elements of the group. If you select either of the legend elements belonging to the group you will not be able to toggle the visibility of the Group layer name. City is the top-most member of the group and its legend item controls the visibility of the Group layer name. For example, if I have group USA with layers City, Road and State. The visibility of the Group Layer Name item is controlled by the top-most member of the group that is present in the legend. This allows you to split group layer items within a legend. This is a bit tricky because the legend list is flat, while the layer list in the map can be nested with group layers and groups within groups. Unfortunately, you have run into a known usability issue. Group layer name support is a recent addition to Pro - see However, I believe your issue is that you want to turn the visibility of the Group Layer Name ( students group layer) and do not know how to do this. If you've attached a new screenshot as opposed to the 2 provided in the original post, they do not seem to be available. ![]() I know that this is different behavior from Pro 2.4, see my comment above that a 2.4 project worked correctly until I saved it, then it did not. But the group layer name is on, and I don't want it to be, and I can't turn it off because the group layer name box is greyed out. The Legend showing on the map has these layers properly ordered (I've changed the order but nothing else). Below are the features, showing the students group layer as turned on. On the left is a portion of the Legend layers, all are selected, even those not visible, and those that are off the screen. On the right is the properties panel with Group Layer name greyed out. So the issue is not that I've set different properties. Nothing I do to that legend, except remove every single feature, brings the group layer name back to unlocked. If I create a brand new legend, all features are in the legend, and when I look at properties, the Group Layer name level is greyed out, though I haven't made any modifications to any feature label. Layer name for Capital item is off, while the layer name for the other elements is on. If I select ALL the legend items again, after turning Capital layer name off, I see that I get the "gray box" next to layer name indicating a property "mismatch" amonth the selected items. These property changes ONLY affect the selected legend items. Here I turned off Layer name and rearrange the label and patch order. If you wish to change properties for a single (or a sub set) of legend items select the item(s) you want to work with from the Contents pane as shown in this example. If you toggle the checkbox once again you will see the layer name for all the selected items appear in the same relative position. If you toggle the check box you can turn off the visibility of the layer name for all items as seen below. Or, as in this case, the positioning of the text name text is not consistent for all selected items. Some could be visible, while others are not. The "gray" box next to Layer name" indicates that the layer name for all the selected elements do not share the same properties. Note that all the legend items are select in the Contents Pane (left side of the screenshot). When I click the "Show properties." button in the Element (Legend) pane the Element pane switches to the "" pane. Note that the layer name is positioned to the left of the symbol for Capital and River, while the layer name States by Region is above the symbols. In this layout I have a legend with 3 items, Capital, River and States by Region. Please see Work with a legend item-Layouts | Documentation for more information on working with legend items. The "grayed out" layer name property in the first screenshot provided in the initial post indicates that the property is not the same for all the selected legend items.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |